: The side deflector and the deflector on a door are open.
11 — the Deflector on a door
12 — the Display and the keyboard
|
|
For the good ventilation preventing a draft, fix the handle of gates of ventilating deflectors (1, 6, 9) in a certain situation. |
Display and keyboard
1 — Defrosting of glasses
2 — the Heating system of back glass (is lower in this Section).
3 — the Mode of use of residual heat of the engine
4 — On/off.
5 — Distribution of air for the right side (automatically, manually)
6 — Economy mode (without cooling)
7 — the Cross over switch of temperature, on the right
8 — the Cross over switch of air supply (automatically, manually)
9 — the Display
Indication on the display is carried out depending on external illumination, black figures on a light background (afternoon), or on the contrary, light figures on a black background (night).
10 — the Cross over switch of temperature, at the left
11 — the air circulation Mode
12 — Distribution of air for the left side (automatically, manually)
13 — the Filter with absorbent carbon
In the automatic mode the automatic conditioner of air makes cooling or heating depending on intensity of the sun, temperature of external air and the required temperature in interior of the car. When using the "Mode of Use of Residual Heat of the Engine" function heating or ventilation of interior of the car can be also made at the switched-off engine.
If economy mode is chosen the cooling system does not work.
It is necessary to change the established temperature only small stages. The automatic conditioner of air can be installed for the left and right parties separately.
The established temperature is reached with the greatest possible speed and supported by a constant.
General recommendations about the automatic conditioner of air
There is a danger of accident!
Visibility can be considerably worsened in view of fogging of glasses if were chosen differing from recommended by us the modes.
The dust removal filter pollen and particles of dust up to the certain size completely is late.
If the salon is heated by the sun, it is necessary to air quickly it prior to the beginning of a trip.
Runduchok between front seats can be ventilated. Ventilation a runduchka on the average console under an armrest (is lower in this Section).
|
|
It is impossible to close air vents in space between a back of a back seat and back glass. |
You hold cuts for an air admission on a cowl free from snow.
On the bottom of the car condensate can be formed.
At coolant leak the conditioner compressor for protection against damage is automatically switched off. The cooling system does not work any more. The economical mode cannot be turned off. In this case to address on one of Mercedes-Benz stations for check of the automatic conditioner of air.
The instruction on environmental protection!
In the automatic conditioner of air R134A coolant is applied. This coolant does not do harm to an ozone layer.
Basic position of governing bodies — in the automatic mode
There are 3 possibilities of the automatic mode:
· Automatic mode of air supply
· Automatic mode of distribution of air at the left and on the right
· Automatic mode of average deflectors
We recommend to you to include all 3 functions of the automatic mode:
Giving and distribution of air are regulated automatically.
At the left and on the right install cross over switches of temperature on 22 °C.
Thereby the most pleasant temperature in the car is reached.
Automatic mode of air supply:
Press the cross over switch of air supply on And. On the display "AUTO" is displayed
Automatic mode of distribution of air:
Press and fix both handles. Symbols, are also not visible any more.
Functions of economy mode and the mode of air circulation are switched off.
The automatic mode of the fan is at the same time activated.
Special provisions — choose only for short time
Manual regulation of distribution of air
Press the handle. The handle starts, symbols are visible, and. Turn the handle according to the required air distribution.
Air outlet from average and side deflectors, deflectors on doors and at a windshield.
Air outlet from average and side, deflectors on doors and at a windshield.
Air outlet from average and side deflectors, deflectors on doors and in space for legs.
Return to automatically mode: Press and fix the handle. Symbols, are also not visible any more.
Manual regulation of air supply
Press the cross over switch of air supply up or down. 7 steps of the fan can be chosen.
Defrosting of glasses
Press the button. On the display it is displayed.
The fan switches to higher step, and heated air goes to deflectors of defrosting of side glasses and a windshield.
By repeated pressing of the button the mode chosen before joins again.
Fogging of glasses from within
If necessary switch off economy mode: press the button. The control light-emitting diode on the button dies away.
If necessary switch off the air circulation mode: press the button. The control light-emitting diode on the button dies away.
At the left and on the right establish air distribution manually up.
Manually establish air supply on the maximum step of the fan.
Increase installation of temperature.
Open side deflectors and turn on side glasses.
Fogging of a windshield outside
Include a screen wiper.
Press and fix both handles. Symbols, are also not visible any more.
Air circulation mode
Include the air circulation mode:
The control light-emitting diode on the button does not burn.
Quickly press the button. On the button the control light-emitting diode lights up.
Switching off of the mode of air circulation:
On the button the control light-emitting diode lights up.
Quickly press the button. The control light-emitting diode on the button dies away.
Inclusion of the mode of air circulation and activation of comfortable closing:
The control light-emitting diode on the button does not burn.
Press the button more than 2 seconds, side glasses and the shifted and lifted top hatch are closed. On the button the control light-emitting diode lights up.
Switching off of the mode of air circulation and activation of comfortable opening:
On the button the control light-emitting diode burns. Press the button more than 2 seconds, side glasses and the shifted and lifted top hatch move to situation in which they were before closing.
If after comfortable closing the window was manually lowered or the shifted and lifted top hatch is open, then at comfortable opening situation in which they were before closing is not reached.
There is a danger of accident!
At a temperature of external air below 5 °C choose the mode of air circulation only for short time, otherwise glasses can mist over.
Switching of the mode of air circulation to the mode of supply of external air is made automatically:
· in 30 minutes at a temperature of external air about 5 °C are above,
· in 5 minutes at a temperature of external air about 5 °C are below,
· in 5 minutes if economy mode was chosen.
At high temperatures of external air there is an automatic switching to the air circulation mode. Approximately in 30 minutes the partial supply of external air begins.
The filter with absorbent carbon and the air circulation considering the external maintenance of OG
The filter significantly reduces concentration of harmful substances and considerably detains smells.
Automatic switching to the mode of air circulation is made if in external air concentration of carbon monoxide (SO) or an oxide of nitrogen (NOh) increased.
The air circulation mode considering the external maintenance of OG is impossible if economy mode or temperature of external air is chosen 5 °C are below.
Turning on of the coal air filter and air circulation, taking into account pollution of external air the fulfilled gases:
The control light-emitting diode on the button does not burn. Quickly press the button. On the button the control light-emitting diode lights up.
Switching off of the coal filter and air circulation, taking into account pollution of external air the fulfilled gases:
On the button the control light-emitting diode lights up.
Quickly press the button. The control light-emitting diode on the button dies away.
Turning on of the coal filter and air circulation, taking into account pollution of external air the fulfilled gases, and activation of comfortable closing:
The control light-emitting diode on the button does not burn. Press the button more than 2 seconds, side glasses and the shifted and lifted top hatch are closed. On the button the control light-emitting diode lights up.
Switching off of the coal filter and air circulation, taking into account pollution of external air the fulfilled gases, and activation of comfortable opening:
On the button the control light-emitting diode burns. Press the button more than 2 seconds, side glasses and the shifted and lifted top hatch move to situation in which they were before closing.
If after comfortable closing the window was manually lowered or the shifted and lifted top hatch is open, then at comfortable opening more situation in which they were before closing is not reached.
"Mode of Use of Residual Heat of the Engine" function
In the "Mode of Use of Residual Heat of the Engine" function heating or ventilation of interior of the car at the switched-off engine are made in the automatic conditioner of air.
Air supply is established automatically.
Before inclusion: turn an electronic key in the lock of ignition in situation 1 or 0 or take out it.
Inclusion of the mode of use of residual heat of the engine: press the button. On the display "REST" is displayed.
Inclusion is impossible if the rechargeable battery is insufficiently charged.
Automatic inclusion:
· if the electronic key in the lock of ignition turns in situation 2.
· approximately in 30 minutes (at the activated "Mode of Use of Residual Heat of the Engine" function on the conditioner in a back part of salon: approximately in 15 minutes),
· if tension of the rechargeable battery falls.
|
|
When falling working tension of the rechargeable battery on the display of the automatic conditioner of air some time before switching off of the "Mode of Use of Residual Heat of the Engine" function is displayed a symbol of the rechargeable battery.
At the included independent heater / ventilation the "Mode of Use of Residual Heat of the Engine" function cannot join. |
Economy mode
Inclusion: press the button. On the button the control light-emitting diode lights up.
The cooling system does not work, and drying of air is not made.
By repeated pressing of the button the mode chosen before is again activated.
In economy mode glasses therefore we do not recommend this mode can mist over.
Switching off/turning on of the automatic conditioner of air
Switching off:
press the button 0. On the display "0" is displayed.
The supply and air circulation are switched off. It is recommended to set this mode only for a short time. Otherwise glasses can mist over.
Inclusion:
press the button 0 or or press and fix at least one handle.
Ventilation a runduchka on the average console under an armrest
In a runduchka towards the lever of the AT selector there is a ventilating nozzle.
Opening: move the handle up.
Closing: move the handle down.
Air supply depends:
· from the established air distribution,
· from the established air supply,
· from the provision of opening of ventilating deflectors on the dashboard.
Air temperature approximately corresponds to air temperature, going out of average deflectors. It cannot be installed separately.
|
|
In a runduchka there can be extremely high temperatures caused by limited space. Therefore when transporting heatsensitive freight it is necessary to close a ventilating nozzle of the included heating.
Do not close a ventilating nozzle in a runduchka objects. |
Deflectors in a back part of salon
1 The adjustable average deflector in a back part of salon, at the left
2 The adjustable average deflector in a back part of salon, on the right
3 The regulator of the average deflector in a back part of salon (model without conditioner in a back part of salon)
Opening: rotate the regulator to the left.
4 The adjustable side deflector in a back part of salon
5 The regulator of deflectors in a back part of salon
Opening: rotate the regulator in the direction of side glass.
The conditioner in a back part of salon
1 On/off the mode of use of residual heat of the engine (is higher in this Section)
2 Display
Indication on the display is carried out depending on external illumination: positively — black figures on a light background (afternoon), or it is negative — light figures on a black background (night).
3 Air distribution above/below
4 Cross over switch of temperature, on the right
5 Cross over switch of air supply
6 Cross over switch of temperature, at the left
7 The adjustable average deflector in a back part of salon, at the left
8 The adjustable average deflector in a back part of salon, on the right
|
|
The conditioner in a back part of salon does not make cooling if the button of the automatic conditioner of air is pressed.
At unoccupied back seats (any of seat belts is not in the belt lock) temperature on both sides automatically is established on 22 °C. |
Basic position of governing bodies in the automatic mode
We recommend to activate the automatic mode and establish temperature at the left and on the right on 22 °C. Thereby, the most pleasant temperature in a back part of salon is reached.
Press the cross over switch of air supply on And. On the display "AUTO" is displayed. Air supply is regulated automatically.
Manual regulation of air supply
Press the cross over switch of air supply up or down. 7 steps of the fan can be chosen.
Control of the conditioner in a back part of salon via the control panel of the automatic conditioner of air
Via the control panel of the automatic conditioner of air on the average console the conditioner in a back part of salon can be switched off and installation of a step of the fan and temperature is changed.
For this purpose on the automatic conditioner of air horizontally press the cross over switch of air supply And yes you hold it pressed until on the display there is no indication given above.
The conditioner in a back part of salon can be switched off and switched on by the button 0.
The fan step, and cross over switches of temperature — conditioner temperature in a back part of salon can be established by the cross over switch of the fan.
Approximately in 4 seconds after the last pressing of the button indication on the display dies away, and the automatic conditioner of air switches to the normal mode of work.
Independent heater
Device of remote control:
1 Antenna
2 Display
3 On/off.
4 Program call button
5 Adjusting buttons
6 Cover
The independent heater makes heating or ventilation of interior of the car depending on the air of value and air temperature established on the automatic conditioner in salon.
The device of remote control can cause all functions of an independent heater. It is possible to include an independent heater at once (immediate heating) or to program so that it automatically joined in the required time (program heating).
By the switch on the average console the independent heater can join and be switched off and be dumped the activated inclusion time.
The independent heater joins only at a temperature of cooling liquid below 70 °C.
There is a danger of ignition and poisoning!
It is impossible to include an independent heater at gas stations and in the enclosed space without extract (for example, in garages).
|
|
At the corresponding temperature and weather conditions can happen that the system, for example, at first makes ventilation, and then — heating. It provides a possibility of achievement of the required temperature with the greatest possible speed. |
For achievement of the maximum radius of operation of the device of remote control the antenna during transfer is recommended to be put forward completely, and you hold the device of remote control vertically. Transfer is made until on the display indication blinks.
The maximum radius of operation of the device of remote control makes 1000 m. From the enclosed space or owing to massive obstacles the radius of action can be limited.
Operating time of an independent heater determined at manufacturer makes 50 minutes. However, it can be established and individually. Any Mercedes-Benz station on this matter will give the reference.
The device of remote control of an independent heater can be stored in a ware compartment, in front of the selector lever, in the holder.
The car is equipped with the device of remote control. For each car one additional device of remote control of the same execution is provided. Any Mercedes-Benz station on this matter will give the reference.
Before inclusion
Installation of the required air temperature in salon by means of cross over switches of temperature of the automatic conditioner of air (is higher in this Section). We recommend to establish temperature at the left and on the right on 22 °C.
The independent heater automatically regulates the established temperature.
Immediate inclusion
Indication on the display of the automatic conditioner of air in the mode of an independent heater.
The independent heater can join the switch on the average console.
Indication on the display of the automatic conditioner of air in the mode of ventilation of an independent heater.
Inclusion of an independent heater switch:
Press the switch a symbol. The green control light-emitting diode lights up, and the display of the automatic conditioner of air is activated.
Inclusion of an independent heater / ventilation device of remote control:
Press the ON button on the device of remote control until on the display of the device of remote control "On" does not begin to blink. The display of the automatic conditioner of air is activated. At inclusion of an independent heater, the control light-emitting diode on the switch on the average console lights up.
Switching off
The independent heater can be switched off by the device of remote control or the switch on the average console.
The independent heater can be switched off by the device of remote control. At turn of an electronic key in the ignition lock in situation 2 the system of ventilation of an independent heater is also switched off.
Switching off by the switch:
press the switch on the average console a symbol. The green control light-emitting diode dies away.
Switching off by the device of remote control:
Press the OFF button on the device of remote control until the display of the device of remote control "OFF" does not begin to blink. The display of the automatic conditioner of air dies away. At the independent heater activated before the green control light-emitting diode on the switch on the average console also dies away.
Inclusion time
Can be set the 3rd time of inclusion, from them it can be activated respectively at one time inclusions.
Remove a cover on the device of remote control and press the program call button. On the display there is inclusion time caused by the last.
Installation of time of inclusion:
Cause the inclusion time which is subject to change, press and you hold pressed the button or until the required time is displayed.
Inclusion of program heating / ventilation
Remove a cover on the device of remote control and repeatedly press the button of a call of the program until on the display the required inclusion time is not displayed.
At once after that press the ON button on the device of remote control until inclusion time begins to blink. On the switch on the average console the yellow control light-emitting diode lights up. The independent heater joins in the required time.
Switching off of program heating / ventilation
The independent heater can be switched off by the device of remote control or the switch on the average console.
Switching off by the switch:
Press the switch on the average console a symbol P off. The yellow control light-emitting diode dies away.
Switching off by the device of remote control:
Remove a cover on the device of remote control and repeatedly press the button of a call of the program until on the display inclusion time is not displayed.
Press the OFF button on the device of remote control until on the display of the device of remote control does not begin to blink "-: - -". On the switch on the average console the yellow control light-emitting diode lights up.
|
|
If the independent heater already joined, then it as "Switching off" is described in the head, can be switched off.
Not later than in 50 minutes the independent heater is automatically switched off. The control light-emitting diode dies away. |
Indication of state of charge of batteries
When falling working tension of the device of remote control is lower than a certain extreme value, when pressing the ON, OFF or R buttons and 10 seconds after transfer on the display indication of "LO" appears. Batteries should be replaced immediately.
Replacement of batteries
1 Cover
2 Batteries
There is a danger of poisoning!
You store batteries far from children. In case of a battery proglatyvaniye immediately see a doctor.
-1-uncover with overcoming provision of fixing down.
Take out an old battery.
Insert a new battery-2-according to markings of poles + and - poured out on the case of the device of remote control.
Pull a cover from below.
The instruction on environmental protection!
You make removal of the discharged batteries according to requirements for environmental protection.
Heating system of back glass
Turn an electronic key in the lock of ignition in situation 2.
Inclusion:
On the control panel of the automatic conditioner of air press the button. On the button the control light-emitting diode lights up.
|
|
In case of frosting of back glass outside or coverings it is necessary to remove with its snow before inclusion of heating of back glass ice and snow. |
The heating system of back glass consumes a lot of electric power. Therefore it should be switched off at once after fogging disappearance.
Heating of back glass is automatically switched off depending on temperature of external air and speed of the movement after about 6 — 23 minutes.
At inclusion of a large number of consumers of the electric power or insufficient state of charge of the rechargeable battery the heating system of back glass can be disconnected.
In this case on the button the control light-emitting diode begins to blink.
At restoration of sufficient tension the heating system of back glass joins automatically again.