|
|
Mercedes S-Class W-220since 1998 releaseRepair and operation of the car |
|
|
Mercedes W220 + Mercedes-Benz cars of the class S (W220) + Operation manual + Routine maintenance + Engine + Cooling system and heating + Power supply system and release + Engine electric equipment + Automatic transmission + Power shafts + Brake system + Suspension bracket and steering + Body - Onboard electric equipment Specifications Diagnostics of malfunctions of onboard electric equipment - the general information Check of the electric motor of a screen wiper Check of the warmed back glass Replacement of glow lamps Function of reserve light Electric safety locks Installation of electric and electronic devices Elements of the uniform lock Arrangement of the basic electric elements of system of electric equipment of a body of the car Anticreeping alarm system + Schemes of electric equipment Immerse yourself in captivating storylines and compelling characters on 123movies. |
Diagnostics of malfunctions of onboard electric equipment - the general information Procedures and codes of diagnostics of systems of electronic control are considered in the Head Elektrooborudovaniye of the engine.The electric component, various switches, the relay, electric motors, safety locks, fusible inserts or breakers of a contour concerning this component and also the conducting and electric sockets serving for connection of a component with the battery and mass of a body can be a part of a typical electric contour. For simplification of a problem of search of malfunctions of electric contours at the end of the Management schematic diagrams of electric connections are enclosed. Before starting works on elimination of malfunctions any of electric contours, attentively study the corresponding scheme as much as possible to have a clear view of its functional purpose. Narrowing of a circle of troubleshooting is usually run due to the gradual identification and an exception which are normally functioning a component of the same contour. At simultaneous failure at once several the component or contours is the most probable cause of refusal burn-out of the corresponding safety lock or violation of grounding (different contours in many cases can become isolated on one safety lock or the plug of weight). Failures of electric equipment often are explained by the elementary reasons, such as corrosion of plugs, failure of a safety lock, combustion of a fusible insert or defect of the relay of switching. Make visual check of a condition of all safety locks, conducting and electric sockets of a contour before starting more concrete check of serviceability its component. In case of application for troubleshooting of diagnostic units carefully plan according to the enclosed electric circuits in what points of a contour and in what sequence it is necessary to connect the device for the purpose of the most effective detection of defect. The tester of electric chains or the voltmeter (12 V a control lamp with a set of connecting wires can be also used), the contour piece continuity indicator (sampler) including a bulb, own power supply and a set of connecting wires are among the main diagnostic units. Besides, it is always necessary to have in the car a set of the wires for start of the engine from an auxiliary source equipped with clips like crocodile and, it is desirable, the contour breaker which can be applied to shunting and connection various electric equipment component in the course of diagnostics of a contour. As it was already mentioned above before starting check of a chain by means of the diagnostic equipment, determine by schemes of the place of its connection. Verification of tension Verifications of tension are made in case of violation of functioning of a contour. Connect one of wires of a tester of electric chains or to a negative pole of the battery, or to well grounded car body point. Other wire of a tester connect to the plug of the electric socket of a contour, preferably the next to the battery or to a safety lock. If the control lamp on a tester lights up, tension on this piece of a chain takes place that confirms serviceability of a contour between this plug and the battery. Continuing to work in a similar manner, investigate the contour rest. Detection of lack of tension speaks about existence of malfunction between this point of a contour and the last from checked earlier (where tension was present). In most cases weakening of electric connections and violation of quality of contacts is a cause of failure.
Searches of short circuit One of methods of searches of short circuit is extraction of a safety lock and connection instead of it of a lamp sampler or the voltmeter. Tension in a contour has to be absent. Pull conducting, watching a lamp sampler. If the lamp begins to blink, somewhere in this plait there is a short circuit on weight which is perhaps caused by wiping of isolation of a wire. Similar check can be made for each of a contour component, including switches. Check of serviceability of grounding This check is made for the purpose of definition of reliability of grounding of a component. Switch-off the battery and connect one of wires of the lamp sampler equipped with the independent power supply to obviously well grounded point. Connect other wire of a lamp to the checked plait or the plug. If the lamp lights up, grounding as it should be (and vice versa). Conductivity verifications Check is made for the purpose of identification of breaks of an electric chain After power off of a contour check it by means of the lamp sampler equipped with the independent battery. Connect sampler wires to both ends of a contour (or by the "power" end (+) and well grounded body point) if the control lamp lights up, the break in a contour is absent. The refusal of inclusion of a lamp demonstrates violation of conductivity of a chain. Similarly it is possible to check also serviceability of the switch, having connected a sampler to its plugs. At transfer of the switch to situation "Vkl" the control lamp sampler has to light up. Break localization At diagnostics of the break of a contour suspected on existence visually to find a cause of defect it appears quite difficult as survey of plugs on existence of corrosion or violation of quality of their contacts is complicated in a type of limitation of access to them (usually plugs are closed by the socket case). Sharp or a plait of its wires in many cases leads twitchings of the case of the socket on the sensor to conductivity restoration. Do not forget about it in attempts of localization of a cause of failure of the contour suspected on break. Unstably arising refusals can have the reason oxidation of plugs or violation of quality of contacts. Diagnostics of malfunctions of electric chains does not represent a stubborn task on condition of a clear idea that current arrives to all electric loadings (a lamp, an electric motor, etc.) from the battery on wires via switches, the relay, safety locks, fusible inserts at all, and then comes back to the battery through the mass of the car. Any problems connected with failure of electric equipment can have the reason only interruptions in supply on them electric current from the battery or its return to it. |
|